China manufacturer and exporter of gear speed reducers
Home >> Products >> NMRV Series Worm-Gear Speed Reducers

NMRVSeries
Worm-Gear Speed Reducers
Worm-gear speed reducer
Worm gears with Pre-stage helical unit
Combination worm gear unit


Combination of speed variator andWorm-gear speed reducer
Torque arm
Output shaft and cover
Input flange B5 and unput flange B14


Shaft input worm-gear speed reducer and combination worm gear unit
G3Series
Helical Gear Reducers


Three-phase motor reducer with foot screw
Three-phase motor reducer with flange
Input-flange reducer with foot screw

Input-flange reducer with output flange
Double-shaft reducer with foot screw
Double-shaft reducer with flange


Combination of stepless variator and input-flange reducer with foot screw


Combination of stepless variator and input-flange reducer with flange
Show the other products


TSRV Series stainless steel
worm-gear reducers
UDL Series speed variators

TR Series helical geared reducers

DC+NMRV series worm-gear reducers


Add:ZiGui Plaza WenErXi Road 268
XiHu, HangZhou Zhejiang Province, China
Tel:0086-571-88220971


Fax:0086-571-88220972
E-mail:shen@www.0571sjpf.com


Technical Data
Lubrication
page 1 of 1
In cases of ambient temperatures not envisaged in the table, call our Technical Service.
● In the case of temperatures under -30°C or over 60°C it is necessary to use oil seals with special material.
● For operating ranges with temperatures under 0°C it is necessary to consider the following:
→ The motors need to be suitable for operation at the envisaged ambient temperature.
→ The power of the electric motor needs to be adequate for exceeding the higher starting torques required.
→ In the case of reduction units with a cast-iron case, pay attention to impact loads since cast iron may have problems of fragility at temperatures under -15°C.
→ During the early stages of service, problems of lubrication may arise due to the high level of viscosity taken on by the oil and so it is wise to have a few minutes of rotation under no load.
The oil needs to be changed after approximately 10,000 hours. This period depends on the type of service and the environment where the reduction unit works.
The reduction units size 025-030-040-050-063-075-090 are supplied complete with lubricant for life, synthetic oil, SHELL TEVELA OIL 320, and can therefore be mounted in any position envisaged in the catalogue. V5/V6 for which you should call our Technical Service to assess the conditions of use.
○ The reduction units size 110 and 130 are supplied complete with lubricant, mineral oil, SHELLTEVELA OIL 320
与陆○变速器速度提供完整bricant, mineral oil, GUANGYAN Ub-3.
○ For sizes 110 and 130 it is necessary to specify the position, otherwise the reduction units are supplied with the quantity of oil relating to pos. B3.
○ Only reduction units 110 and 130 are fitted with breather, level and oil drainage plugs. It is necessary, after installation, to replace the closed plug used for transportation with the breather plug supplied with the unit.
○ PC is supplied complete with life-long lubricant, synthetic oil, SHELL TEVELA OIL 320, and can therefore be mounted in all the positions. Lubrication is separated from that of the worm reduction unit.
Specifications of lubricants
Quantity of oil in litres
NMRV
025
030
040
050
063
075
090
110
130
PC
63
71
80
90
B3
0.023
0.05
0.1
0.15
0.3
0.5
1
3
4.5
0.05
0.07
0.15
0.16
B8
2.2
3.3
B6-B7
2.5
3.5
V5
3
4.5
V6
2.2
3.3
UDL
UDL0.18
UDL0.37
UDL0.55
UDL0.75
UD1.1
UD1.5
UD2.2
UD3
UD4
B3
0.13
0.15
0.33
0.33
0.8
0.8
1.2
1.2
1.2
B8
B6-B7
V5
0.2
0.25
0.45
0.45
1
1
1.2
1.2
1.2
V6
0.3
0.4
0.85
0.85
1.4
1.4
2.15
2.15
2.15

Product Description Contents
1.Guide of type selection
2.Technical data
1)Service factor
2)The admissible radial load on the shaft
3)Efficiency & Irreversibility character
4)Mesh parameter
5)Lubrication
6)Installation
7)Critical application
8)Motor coupling
9)PC features and mounting
10)Mounting positions
11)Direction of rotation
12)Performance parameter

3.Notice for ordering
4.Exploded view & name


UDL speed variators| Worm reducers |CycloIdal gear reducers Gearbox for Agricultural Machinery Planetary gearboxes Helical Geared motors spiral bevel geared motors DC small size geared motors GEARBOXES FOR TRACTORS & AUTO Special Reducers & gearboxes Worm Gearboxes for Irrigation system

Baidu